修复源代码中文注释乱码并统一为UTF-8编码，Lora频率改为470MHz频段
1. 修复 source/inc/bsp.h、source/inc/main.h、source/src/bsp.c 中文注释乱码，统一保存为UTF-8编码 2. Lora中心频率由433.1MHz改为470.1MHz~492.6MHz，步进500kHz，共46个信道(CH0~CH45) 3. 新增下载前配置检查注释块，LORA_FREQ默认信道改为CH0 4. 更新Keil调试配置(CMSIS_AGDI调试器及观察窗口设置)
This commit is contained in:
+96
-57
@@ -5,68 +5,107 @@
|
||||
#include <stdbool.h>
|
||||
#include "gpio.h"
|
||||
|
||||
/*设备类型*/
|
||||
#define FORCE_6D 0x0001 //0x0001 六维应力
|
||||
#define OSMOTIC_PRESSURE 0x0002 //0x0002 渗透压
|
||||
#define ELASTIC_WAVEGUIDE 0x0003 //0x0003 弹性波导
|
||||
#define DIELECTRIC_MASS 0x0004 //0x0004 介电质普
|
||||
#define _0x0005 0x0005 //0x0005 保留
|
||||
#define CONT_DEFOR_3D 0x0006 //0x0006 三维连续变形
|
||||
#define COMM_UNIT 0x0007 //0x0007 通讯单元
|
||||
#define FORCE_3D 0x0008 //0x0008 三维应力
|
||||
#define LASER_TRACING 0x0009 //0x0009 激光示踪
|
||||
#define _0x000A 0x000A //0x000A 保留
|
||||
#define _0x000B 0x000B //0x000B 保留
|
||||
#define _0x000C 0x000C //0x000C 保留
|
||||
#define MULTI_PARAMETER_FUSION 0x000D //0x000D 多参数融合
|
||||
#define CRACK_DETECTION 0x000E //0x000E 裂缝仪
|
||||
#define _0x000F 0x000F //0x000F 保留
|
||||
#define ATTITUDE_MONITOR 0x0010 //0x0010 姿态检测
|
||||
#define LASER_DISPLACE 0x0011 //0x0011 激光位移
|
||||
#define REBAR_STRESS 0x0012 //0x0012 钢筋应力
|
||||
#define ANCHOR_ROD_STRESS 0x0013 //0x0013 锚杆轴力
|
||||
#define SURFACE_STRESS 0x0014 //0x0014 表面应力
|
||||
#define PRESSURE 0x0015 //0x0015 压力
|
||||
#define MICROWAVE_DISPLACE 0x0016 //0x0016 微波测距
|
||||
/*通讯方式*/
|
||||
/*设备类型*/
|
||||
#define FORCE_6D 0x0001 //0x0001 六维应力
|
||||
#define OSMOTIC_PRESSURE 0x0002 //0x0002 渗透压
|
||||
#define ELASTIC_WAVEGUIDE 0x0003 //0x0003 弹性波导
|
||||
#define DIELECTRIC_MASS 0x0004 //0x0004 介电质谱
|
||||
#define _0x0005 0x0005 //0x0005 保留
|
||||
#define CONT_DEFOR_3D 0x0006 //0x0006 三维连续变形
|
||||
#define COMM_UNIT 0x0007 //0x0007 通讯单元
|
||||
#define FORCE_3D 0x0008 //0x0008 三维应力
|
||||
#define LASER_TRACING 0x0009 //0x0009 激光示踪
|
||||
#define _0x000A 0x000A //0x000A 保留
|
||||
#define _0x000B 0x000B //0x000B 保留
|
||||
#define _0x000C 0x000C //0x000C 保留
|
||||
#define MULTI_PARAMETER_FUSION 0x000D //0x000D 多参数融合
|
||||
#define CRACK_DETECTION 0x000E //0x000E 裂缝检测
|
||||
#define _0x000F 0x000F //0x000F 保留
|
||||
#define ATTITUDE_MONITOR 0x0010 //0x0010 姿态检测
|
||||
#define LASER_DISPLACE 0x0011 //0x0011 激光位移
|
||||
#define REBAR_STRESS 0x0012 //0x0012 钢筋应力
|
||||
#define ANCHOR_ROD_STRESS 0x0013 //0x0013 锚杆轴力
|
||||
#define SURFACE_STRESS 0x0014 //0x0014 表面应力
|
||||
#define PRESSURE 0x0015 //0x0015 压力
|
||||
#define MICROWAVE_DISPLACE 0x0016 //0x0016 微波测距
|
||||
/*通讯方式*/
|
||||
typedef enum {
|
||||
LORA = 0x01, //0x01 LORA通讯
|
||||
RS485 = 0x02, //0x02 RS485通讯
|
||||
RS232 = 0x03, //0x03 RS232通讯
|
||||
CAN = 0x04, //0x04 CAN通讯
|
||||
_4G = 0x05, //0x05 _4G通讯
|
||||
BLE = 0x06, //0x06 BLE通讯
|
||||
WIFI = 0x07, //0x07 WIFI通讯
|
||||
LORA = 0x01, //0x01 LORA通讯
|
||||
RS485 = 0x02, //0x02 RS485通讯
|
||||
RS232 = 0x03, //0x03 RS232通讯
|
||||
CAN = 0x04, //0x04 CAN通讯
|
||||
_4G = 0x05, //0x05 _4G通讯
|
||||
BLE = 0x06, //0x06 BLE通讯
|
||||
WIFI = 0x07, //0x07 WIFI通讯
|
||||
}COMM_WAY_M;
|
||||
/*设备标志*/
|
||||
/*设备标志*/
|
||||
typedef enum {
|
||||
MASTER = 0x000000, //0x000000 主设备
|
||||
SUBSET = 0x800000, //0x800000 子设备
|
||||
MASTER = 0x000000, //0x000000 主设备
|
||||
SUBSET = 0x800000, //0x800000 子设备
|
||||
}DEVICE_SIGN_M;
|
||||
/*Lora频率：433100000ul + 200000*N */
|
||||
/*Lora频率：470100000ul + 500000*N */
|
||||
typedef enum {
|
||||
CH0 = (433100000ul + 0), //测试频率
|
||||
CH1 = (433100000ul + 200000),
|
||||
CH2 = (433100000ul + 400000),
|
||||
CH3 = (433100000ul + 600000),
|
||||
CH4 = (433100000ul + 800000),
|
||||
CH5 = (433100000ul + 1000000),
|
||||
CH6 = (433100000ul + 1200000),
|
||||
CH7 = (433100000ul + 1400000),
|
||||
CH8 = (433100000ul + 1600000),
|
||||
CH9 = (433100000ul + 1800000),
|
||||
CH10 = (433100000ul + 2000000),
|
||||
CH0 = (470100000ul + 0), //测试频率
|
||||
CH1 = (470100000ul + 500000),
|
||||
CH2 = (470100000ul + 1000000),
|
||||
CH3 = (470100000ul + 1500000),
|
||||
CH4 = (470100000ul + 2000000),
|
||||
CH5 = (470100000ul + 2500000),
|
||||
CH6 = (470100000ul + 3000000),
|
||||
CH7 = (470100000ul + 3500000),
|
||||
CH8 = (470100000ul + 4000000),
|
||||
CH9 = (470100000ul + 4500000),
|
||||
CH10 = (470100000ul + 5000000),
|
||||
CH11 = (470100000ul + 5500000),
|
||||
CH12 = (470100000ul + 6000000),
|
||||
CH13 = (470100000ul + 6500000),
|
||||
CH14 = (470100000ul + 7000000),
|
||||
CH15 = (470100000ul + 7500000),
|
||||
CH16 = (470100000ul + 8000000),
|
||||
CH17 = (470100000ul + 8500000),
|
||||
CH18 = (470100000ul + 9000000),
|
||||
CH19 = (470100000ul + 9500000),
|
||||
CH20 = (470100000ul + 10000000),
|
||||
CH21 = (470100000ul + 10500000),
|
||||
CH22 = (470100000ul + 11000000),
|
||||
CH23 = (470100000ul + 11500000),
|
||||
CH24 = (470100000ul + 12000000),
|
||||
CH25 = (470100000ul + 12500000),
|
||||
CH26 = (470100000ul + 13000000),
|
||||
CH27 = (470100000ul + 13500000),
|
||||
CH28 = (470100000ul + 14000000),
|
||||
CH29 = (470100000ul + 14500000),
|
||||
CH30 = (470100000ul + 15000000),
|
||||
CH31 = (470100000ul + 15500000),
|
||||
CH32 = (470100000ul + 16000000),
|
||||
CH33 = (470100000ul + 16500000),
|
||||
CH34 = (470100000ul + 17000000),
|
||||
CH35 = (470100000ul + 17500000),
|
||||
CH36 = (470100000ul + 18000000),
|
||||
CH37 = (470100000ul + 18500000),
|
||||
CH38 = (470100000ul + 19000000),
|
||||
CH39 = (470100000ul + 19500000),
|
||||
CH40 = (470100000ul + 20000000),
|
||||
CH41 = (470100000ul + 20500000),
|
||||
CH42 = (470100000ul + 21000000),
|
||||
CH43 = (470100000ul + 21500000),
|
||||
CH44 = (470100000ul + 22000000),
|
||||
CH45 = (470100000ul + 22500000), //最高频率
|
||||
}LORA_FREQ_M;
|
||||
/*设备类型选择*/
|
||||
/*****************************************************************************************/
|
||||
/*********************************下载前必须检查配置项************************************/
|
||||
/*设备类型选择*/
|
||||
#define DEVICE_TYPE LASER_TRACING
|
||||
/*通讯方式选择*/
|
||||
/*通讯方式选择*/
|
||||
#define COMM_WAY LORA
|
||||
/*设备标志选择*/
|
||||
/*设备标志选择*/
|
||||
#define DEVICE_SIGN MASTER
|
||||
/*设备地址编号设置*/
|
||||
#define ADD_NUMBER (0x000023 + DEVICE_SIGN) //数字部分对应唯一地址编号
|
||||
/*Lora频率配置*/
|
||||
#define LORA_FREQ CH1
|
||||
/*设备地址编号设置*/
|
||||
#define ADD_NUMBER (0x000023 + DEVICE_SIGN) //数字部分对应唯一地址编号
|
||||
/*Lora频率配置*/
|
||||
#define LORA_FREQ CH0
|
||||
/*****************************************************************************************/
|
||||
/*********************************下载前必须检查配置项************************************/
|
||||
|
||||
#if(DEVICE_TYPE == LASER_TRACING)
|
||||
#define LP_UART_CH 0
|
||||
@@ -229,7 +268,7 @@ typedef enum {
|
||||
#define USE_LOWPOWER 0
|
||||
#define USE_WDT 1
|
||||
|
||||
//#define WAKEUP_TIME_ARR (65536 - (30 * 150)) //65536 - time * 38400Hz / 256分频
|
||||
//#define WAKEUP_TIME_ARR (65536 - (30 * 150)) //65536 - time * 38400Hz / 256分频
|
||||
|
||||
#define SYSCLK_RCH 0
|
||||
#define SYSCLK_XTH 1
|
||||
@@ -243,9 +282,9 @@ typedef struct {
|
||||
uint32_t PackageCnt;
|
||||
uint32_t AppSize;
|
||||
uint32_t Crc32Check;
|
||||
uint32_t FirstRunFlag;//第一次运行
|
||||
uint8_t DevMac[6];//设备MAC
|
||||
uint32_t LoraFreq;//Lora频率
|
||||
uint32_t FirstRunFlag;//第一次运行
|
||||
uint8_t DevMac[6];//设备MAC
|
||||
uint32_t LoraFreq;//Lora频率
|
||||
}BootPara_t, *BootPara;
|
||||
|
||||
typedef void (*ReadPara)(BootPara_t rPara);
|
||||
|
||||
+8
-8
@@ -10,13 +10,13 @@
|
||||
|
||||
typedef enum {
|
||||
UPDATE_CMD_NULL,
|
||||
UPDATE_CMD_SLAVE_RES, //从机应答主机下发
|
||||
UPDATE_CMD_SLAVE_REQ_DATA, //从机请求主机下发数据
|
||||
UPDATE_CMD_MASTER_REQ = 0x81, //主机请求升级
|
||||
UPDATE_CMD_MASTRE_RES_DATA, //主机发送数据
|
||||
UPDATE_CMD_SLAVE_RES, //从机应答主机下发
|
||||
UPDATE_CMD_SLAVE_REQ_DATA, //从机请求主机下发数据
|
||||
UPDATE_CMD_MASTER_REQ = 0x81, //主机请求升级
|
||||
UPDATE_CMD_MASTRE_RES_DATA, //主机发送数据
|
||||
}UpdateCmd_m;
|
||||
|
||||
//帧头结构体
|
||||
//帧头结构体
|
||||
typedef struct {
|
||||
uint8_t Header;
|
||||
uint8_t DevMac[6];
|
||||
@@ -24,20 +24,20 @@ typedef struct {
|
||||
uint8_t PayloadLen;
|
||||
}__attribute__ ((packed))FrameHeader_t, *FrameH;
|
||||
|
||||
//主机下发升级请求载荷结构体
|
||||
//主机下发升级请求载荷结构体
|
||||
typedef struct {
|
||||
uint16_t PackageNum;
|
||||
uint32_t AppSize;
|
||||
uint32_t AppCrc32;
|
||||
}__attribute__ ((packed))UpDataRequset_t, *UDReq;
|
||||
|
||||
//从机请求下发结构体
|
||||
//从机请求下发结构体
|
||||
typedef struct {
|
||||
uint16_t PackageIndex;
|
||||
uint32_t PackageNum;
|
||||
}__attribute__ ((packed))GetDataRequest_t, *GDReq;
|
||||
|
||||
//主机应答下发数据结构体
|
||||
//主机应答下发数据结构体
|
||||
typedef struct {
|
||||
uint16_t PackageIndex;
|
||||
uint16_t PackageNum;
|
||||
|
||||
+49
-49
@@ -22,20 +22,20 @@ static __IO bool LpUart0_Tx_Flag;
|
||||
|
||||
static void SystemClkInit(en_sysctrl_rch_freq_t enRchFreq)
|
||||
{
|
||||
///< RCH时钟不同频率的切换，需要先将时钟切换到RCL
|
||||
///< RCH时钟不同频率的切换，需要先将时钟切换到RCL
|
||||
Sysctrl_SetRCLTrim(SysctrlRclFreq32768);
|
||||
Sysctrl_SetRCLStableTime(SysctrlRclStableCycle64);
|
||||
Sysctrl_ClkSourceEnable(SysctrlClkRCL, TRUE);
|
||||
Sysctrl_SysClkSwitch(SysctrlClkRCL);
|
||||
|
||||
///< 加载目标频率的RCH的TRIM值
|
||||
///< 加载目标频率的RCH的TRIM值
|
||||
Sysctrl_SetRCHTrim(enRchFreq);
|
||||
///< 使能RCH
|
||||
///< 使能RCH
|
||||
Sysctrl_ClkSourceEnable(SysctrlClkRCH, TRUE);
|
||||
///< 时钟切换到RCH
|
||||
///< 时钟切换到RCH
|
||||
Sysctrl_SysClkSwitch(SysctrlClkRCH);
|
||||
|
||||
///< HCLK不超过24M：此处设置FLASH读等待周期为0 cycle
|
||||
///< HCLK不超过24M：此处设置FLASH读等待周期为0 cycle
|
||||
Flash_WaitCycle(FlashWaitCycle0);
|
||||
}
|
||||
|
||||
@@ -43,14 +43,14 @@ static void SystemClkInit(en_sysctrl_rch_freq_t enRchFreq)
|
||||
|
||||
static void SystemClkInit(en_sysctrl_xth_freq_t enXthFreq)
|
||||
{
|
||||
///<======================== 切换至XTH32MHz ==============================
|
||||
///< 当使用的时钟源HCLK大于24M：设置FLASH 读等待周期为1 cycle(默认值也为1 cycle)
|
||||
///<======================== 切换至XTH32MHz ==============================
|
||||
///< 当使用的时钟源HCLK大于24M：设置FLASH 读等待周期为1 cycle(默认值也为1 cycle)
|
||||
if(SysctrlXthFreq24_32MHz == enXthFreq)
|
||||
{
|
||||
Flash_WaitCycle(FlashWaitCycle1);
|
||||
}
|
||||
|
||||
///< 切换时钟前（根据外部高速晶振）设置XTH频率范围,配置晶振参数，使能目标时钟，此处为SYSTEM_XTH = 32MHz
|
||||
///< 切换时钟前（根据外部高速晶振）设置XTH频率范围,配置晶振参数，使能目标时钟，此处为SYSTEM_XTH = 32MHz
|
||||
Sysctrl_SetXTHFreq(enXthFreq);
|
||||
Sysctrl_XTHDriverCfg(SysctrlXtalDriver3);
|
||||
Sysctrl_SetXTHStableTime(SysctrlXthStableCycle16384);
|
||||
@@ -62,16 +62,16 @@ static void SystemClkInit(en_sysctrl_xth_freq_t enXthFreq)
|
||||
{
|
||||
Flash_WaitCycle(FlashWaitCycle0);
|
||||
}
|
||||
//M0P_SYSCTRL->SYSCTRL0_f.WAKEUP_BYRCH = 0; //唤醒保持原时钟
|
||||
//M0P_SYSCTRL->SYSCTRL0_f.WAKEUP_BYRCH = 0; //唤醒保持原时钟
|
||||
}
|
||||
|
||||
#elif (SYSCLK == SYSCLK_PLL)
|
||||
///<请注意根据外部晶振配置宏——[SYSTEM_XTH],如果使用PLL，XTH必须小于24MHz
|
||||
///<请注意根据外部晶振配置宏——[SYSTEM_XTH],如果使用PLL，XTH必须小于24MHz
|
||||
static void SystemClkInit(void)
|
||||
{
|
||||
stc_sysctrl_pll_cfg_t stcPLLCfg;
|
||||
|
||||
///< 切换时钟前（根据外部高速晶振）设置XTH频率范围,配置晶振参数，使能目标时钟，此处为SYSTEM_XTH = 32MHz
|
||||
///< 切换时钟前（根据外部高速晶振）设置XTH频率范围,配置晶振参数，使能目标时钟，此处为SYSTEM_XTH = 32MHz
|
||||
// Sysctrl_SetXTHFreq(SysctrlXthFreq4_8MHz);
|
||||
// Sysctrl_XTHDriverCfg(SysctrlXtalDriver3);
|
||||
// Sysctrl_SetXTHStableTime(SysctrlXthStableCycle16384);
|
||||
@@ -82,17 +82,17 @@ static void SystemClkInit(void)
|
||||
delay1ms(10);
|
||||
|
||||
stcPLLCfg.enInFreq = SysctrlPllInFreq6_12MHz; //XTH 8MHz
|
||||
stcPLLCfg.enOutFreq = SysctrlPllOutFreq36_48MHz; //PLL 输出
|
||||
stcPLLCfg.enPllClkSrc = SysctrlPllRch; //输入时钟源选择RCH
|
||||
stcPLLCfg.enOutFreq = SysctrlPllOutFreq36_48MHz; //PLL 输出
|
||||
stcPLLCfg.enPllClkSrc = SysctrlPllRch; //输入时钟源选择RCH
|
||||
stcPLLCfg.enPllMul = SysctrlPllMul6; //8MHz x 6 = 48MHz
|
||||
Sysctrl_SetPLLFreq(&stcPLLCfg);
|
||||
|
||||
///< 当使用的时钟源HCLK大于24M：设置FLASH 读等待周期为1 cycle(默认值也为1 cycle)
|
||||
///< 当使用的时钟源HCLK大于24M：设置FLASH 读等待周期为1 cycle(默认值也为1 cycle)
|
||||
Flash_WaitCycle(FlashWaitCycle1);
|
||||
|
||||
///< 使能PLL
|
||||
///< 使能PLL
|
||||
Sysctrl_ClkSourceEnable(SysctrlClkPLL, TRUE);
|
||||
///< 时钟切换到PLL
|
||||
///< 时钟切换到PLL
|
||||
Sysctrl_SysClkSwitch(SysctrlClkPLL);
|
||||
|
||||
}
|
||||
@@ -100,9 +100,9 @@ static void SystemClkInit(void)
|
||||
|
||||
static void SystemRCLInit(void)
|
||||
{
|
||||
Sysctrl_SetRCLTrim(SysctrlRclFreq38400); ///< 配置RCL时钟为32kHz
|
||||
Sysctrl_SetRCLTrim(SysctrlRclFreq38400); ///< 配置RCL时钟为32kHz
|
||||
Sysctrl_SetRCLStableTime(SysctrlRclStableCycle256);
|
||||
Sysctrl_ClkSourceEnable(SysctrlClkRCL, TRUE); ///< 使能RCL时钟
|
||||
Sysctrl_ClkSourceEnable(SysctrlClkRCL, TRUE); ///< 使能RCL时钟
|
||||
}
|
||||
|
||||
static void LPUartInit(void)
|
||||
@@ -116,32 +116,32 @@ static void LPUartInit(void)
|
||||
///<TX
|
||||
stcGpioCfg.enDir = GpioDirOut;
|
||||
Gpio_Init(LPUART_TX_PORT, LPUART_TX_PIN, &stcGpioCfg);
|
||||
Gpio_SetAfMode(LPUART_TX_PORT, LPUART_TX_PIN, LPUART_TX_AF); //配置PA00为LPUART1_TX
|
||||
Gpio_SetAfMode(LPUART_TX_PORT, LPUART_TX_PIN, LPUART_TX_AF); //配置PA00为LPUART1_TX
|
||||
|
||||
//<RX
|
||||
stcGpioCfg.enDir = GpioDirIn;
|
||||
Gpio_Init(LPUART_RX_PORT, LPUART_RX_PIN,&stcGpioCfg);
|
||||
Gpio_SetAfMode(LPUART_RX_PORT, LPUART_RX_PIN, LPUART_RX_AF); //配置PA01为LPUART1_RX
|
||||
Gpio_SetAfMode(LPUART_RX_PORT, LPUART_RX_PIN, LPUART_RX_AF); //配置PA01为LPUART1_RX
|
||||
|
||||
DDL_ZERO_STRUCT(stcCfg);
|
||||
Sysctrl_SetPeripheralGate(LPUART_PERIPHERAL_CLK,TRUE);
|
||||
|
||||
///<LPUART 初始化
|
||||
stcCfg.enStopBit = LPUart1bit; ///<1停止位
|
||||
stcCfg.enMmdorCk = LPUartEven; ///<偶校验
|
||||
stcCfg.stcBaud.enSclkSel = LPUartMskRcl; ///<传输时钟源
|
||||
stcCfg.stcBaud.u32Sclk = 38400; ///<PCLK获取
|
||||
stcCfg.stcBaud.enSclkDiv = LPUartMsk4Or8Div; ///<采样分频
|
||||
stcCfg.stcBaud.u32Baud = 9600; ///<波特率
|
||||
stcCfg.enRunMode = LPUartMskMode1; ///<工作模式
|
||||
///<LPUART 初始化
|
||||
stcCfg.enStopBit = LPUart1bit; ///<1停止位
|
||||
stcCfg.enMmdorCk = LPUartEven; ///<偶校验
|
||||
stcCfg.stcBaud.enSclkSel = LPUartMskRcl; ///<传输时钟源
|
||||
stcCfg.stcBaud.u32Sclk = 38400; ///<PCLK获取
|
||||
stcCfg.stcBaud.enSclkDiv = LPUartMsk4Or8Div; ///<采样分频
|
||||
stcCfg.stcBaud.u32Baud = 9600; ///<波特率
|
||||
stcCfg.enRunMode = LPUartMskMode1; ///<工作模式
|
||||
LPUart_Init(LPUART, &stcCfg);
|
||||
|
||||
///<LPUART 中断使能
|
||||
LPUart_ClrStatus(LPUART,LPUartRC); ///<清接收中断请求
|
||||
LPUart_ClrStatus(LPUART,LPUartTC); ///<清发送中断请求
|
||||
LPUart_EnableIrq(LPUART,LPUartTxIrq); ///<使能发送中断
|
||||
LPUart_EnableIrq(LPUART,LPUartRxIrq); ///<使能接收中断
|
||||
EnableNvic(LPUART_IRQN,IrqLevel3,TRUE); ///<系统中断使能
|
||||
///<LPUART 中断使能
|
||||
LPUart_ClrStatus(LPUART,LPUartRC); ///<清接收中断请求
|
||||
LPUart_ClrStatus(LPUART,LPUartTC); ///<清发送中断请求
|
||||
LPUart_EnableIrq(LPUART,LPUartTxIrq); ///<使能发送中断
|
||||
LPUart_EnableIrq(LPUART,LPUartRxIrq); ///<使能接收中断
|
||||
EnableNvic(LPUART_IRQN,IrqLevel3,TRUE); ///<系统中断使能
|
||||
}
|
||||
|
||||
void DBGUartSend(uint8_t *sData, int sLen)
|
||||
@@ -167,13 +167,13 @@ void DBGUartSend(uint8_t *sData, int sLen)
|
||||
void LpUart0_IRQHandler(void)
|
||||
{
|
||||
if(LPUart_GetStatus(LPUART, LPUartTC)) {
|
||||
LPUart_ClrStatus(LPUART, LPUartTC); ///<清发送中断请求
|
||||
LPUart_ClrStatus(LPUART, LPUartTC); ///<清发送中断请求
|
||||
LpUart0_Tx_Flag = true;
|
||||
}
|
||||
|
||||
if(LPUart_GetStatus(LPUART, LPUartRC)) { ///接收数据
|
||||
LPUart_ClrStatus(LPUART, LPUartRC); ///<清接收中断请求
|
||||
uint8_t u8RxData = LPUart_ReceiveData(LPUART); ///读取数据
|
||||
if(LPUart_GetStatus(LPUART, LPUartRC)) { ///接收数据
|
||||
LPUart_ClrStatus(LPUART, LPUartRC); ///<清接收中断请求
|
||||
uint8_t u8RxData = LPUart_ReceiveData(LPUART); ///读取数据
|
||||
DebugUartIRQ(u8RxData);
|
||||
}
|
||||
}
|
||||
@@ -181,13 +181,13 @@ void LpUart0_IRQHandler(void)
|
||||
void LpUart1_IRQHandler(void)
|
||||
{
|
||||
if(LPUart_GetStatus(LPUART, LPUartTC)) {
|
||||
LPUart_ClrStatus(LPUART, LPUartTC); ///<清发送中断请求
|
||||
LPUart_ClrStatus(LPUART, LPUartTC); ///<清发送中断请求
|
||||
LpUart0_Tx_Flag = true;
|
||||
}
|
||||
|
||||
if(LPUart_GetStatus(LPUART, LPUartRC)) { ///接收数据
|
||||
LPUart_ClrStatus(LPUART, LPUartRC); ///<清接收中断请求
|
||||
uint8_t u8RxData = LPUart_ReceiveData(LPUART); ///读取数据
|
||||
if(LPUart_GetStatus(LPUART, LPUartRC)) { ///接收数据
|
||||
LPUart_ClrStatus(LPUART, LPUartRC); ///<清接收中断请求
|
||||
uint8_t u8RxData = LPUart_ReceiveData(LPUART); ///读取数据
|
||||
DebugUartIRQ(u8RxData);
|
||||
}
|
||||
}
|
||||
@@ -200,12 +200,12 @@ static void GPIOInit(void)
|
||||
DDL_ZERO_STRUCT(GpioInitStruct);
|
||||
Sysctrl_SetPeripheralGate(SysctrlPeripheralGpio,TRUE);
|
||||
|
||||
GpioInitStruct.enDir = GpioDirOut; ///< 端口方向配置->输入
|
||||
GpioInitStruct.enDrv = GpioDrvH; ///< 端口驱动能力配置->高驱动能力
|
||||
GpioInitStruct.enPu = GpioPuDisable; ///< 端口上下拉配置->无
|
||||
GpioInitStruct.enDir = GpioDirOut; ///< 端口方向配置->输入
|
||||
GpioInitStruct.enDrv = GpioDrvH; ///< 端口驱动能力配置->高驱动能力
|
||||
GpioInitStruct.enPu = GpioPuDisable; ///< 端口上下拉配置->无
|
||||
GpioInitStruct.enPd = GpioPdDisable;
|
||||
GpioInitStruct.enOD = GpioOdDisable; ///< 端口开漏输出配置->开漏输出关闭
|
||||
GpioInitStruct.enCtrlMode = GpioAHB; ///< 端口输入/输出值寄存器总线控制模式配置->AHB
|
||||
GpioInitStruct.enOD = GpioOdDisable; ///< 端口开漏输出配置->开漏输出关闭
|
||||
GpioInitStruct.enCtrlMode = GpioAHB; ///< 端口输入/输出值寄存器总线控制模式配置->AHB
|
||||
GpioInitStruct.bOutputVal = false;
|
||||
|
||||
Gpio_Init(RS485_CTRL_PORT, RS485_CTRL_PIN, &GpioInitStruct);
|
||||
@@ -215,9 +215,9 @@ static void GPIOInit(void)
|
||||
static void WdtInit(void)
|
||||
{
|
||||
#if (USE_WDT == 1)
|
||||
///< 开启WDT外设时钟
|
||||
///< 开启WDT外设时钟
|
||||
Sysctrl_SetPeripheralGate(SysctrlPeripheralWdt,TRUE);
|
||||
///< WDT 初始化
|
||||
///< WDT 初始化
|
||||
Wdt_Init(WdtResetEn, WdtT52s4);
|
||||
Wdt_Start();
|
||||
#endif
|
||||
|
||||
Reference in New Issue
Block a user