feat(debug): 新增 up 上传网关状态和 reg 重新注册命令

1.  修正所有RS485通道配置结构体的成员命名错误，将CUData改为CUPara
2.  新增bsp头文件引用，补充ETHStop、ETHReset相关调用
3.  调整通信切换时的服务器注册标志重置与外设复位逻辑

DebugCmd.c

@@ -1,4 +1,5 @@
 #include "main.h"
+#include "bsp.h"
 #include "CatOneTask.h"
 #include "RS485Task.h"
 #include "Public.h"
@@ -8,7 +9,7 @@
 
 #define	DBG_RX_LEN_MAX				128
 //#define	DBG_LOG(...)									rt_kprintf(__VA_ARGS__)
-#define DEBUG_CMD_CNT					22
+#define DEBUG_CMD_CNT					30
 #define	DEBUG_BUFF_SIZE_MAX		512
 
 #define DEBUG_BUFSIZE 						200
@@ -259,15 +260,15 @@ void DebugCmdRS485Ctrl(int argc, char *argv[])
 		return;
 	
 	if(strcmp(argv[1], "?") == 0) {
-		DBG_LOG("Debug Cmd: rs485 arg1 arg2 arg3 arg4\r\n");
+		DBG_LOG("Debug Cmd: rs485 arg1 arg2 arg3\r\n");
 		DBG_LOG("  brief --> RS485 control command.\r\n");
 		DBG_LOG("  arg1  --> idx: (1, 2) RS485 channel selection.\r\n");
-		DBG_LOG("  arg2  --> scmd:(o, c, v, b)Rs485 subcommand.\r\n");
+		DBG_LOG("  arg2  --> scmd:(o, c, v, b, u)Rs485 subcommand.\r\n");
 		DBG_LOG("            scmd = o, arg3 = (on, off) RS485 Channel On-OFF.\r\n");
 		DBG_LOG("            scmd = c, arg3 = (on, off) Enable the internal communication unit function.\r\n");
 		DBG_LOG("            scmd = v, arg3 = (on, off) Set output voltage.\r\n");
-		DBG_LOG("            scmd = b, arg3 = (2400~500000) Set baud rate.\r\n\r\n");
+		DBG_LOG("            scmd = b, arg3 = (2400~500000) Set baud rate.\r\n");
-		DBG_LOG("            scmd = u, arg4 = (on, off) Set Upgrade symbol.\r\n\r\n");
+		DBG_LOG("            scmd = u, arg3 = (on, off) Set Upgrade symbol.\r\n\r\n");
 		return;
 	}
 	
@@ -301,9 +302,9 @@ void DebugCmdRS485Ctrl(int argc, char *argv[])
 				if(idx == 1) {
 					GateWay->ConfigPara.Rs485Ch1.CommUnitEnable = true;
 					GateWay->ConfigPara.Rs485Ch1.QuerySensorFlag = true;
-					GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorN = 0;
+					GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorN = 0;
-					memset(GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorType, 0x00, SENSOR_NUM_MAX * 2);
+					memset(GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorType, 0x00, SENSOR_NUM_MAX * 2);
-					GateWay->ConfigPara.Rs485Ch1.CUData.Para.CommStatus = true;
+					GateWay->ConfigPara.Rs485Ch1.CUPara.Para.CommStatus = true;
 					RS485Ch1_Config(9600);
 					GateWay->ConfigPara.Rs485Ch1.BaudRate = 9600;
 					SComm1Para.SensorCnt = 0;
@@ -311,9 +312,9 @@ void DebugCmdRS485Ctrl(int argc, char *argv[])
 				else if(idx == 2) {
 					GateWay->ConfigPara.Rs485Ch2.CommUnitEnable = true;
 					GateWay->ConfigPara.Rs485Ch2.QuerySensorFlag = true;
-					GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorN = 0;
+					GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorN = 0;
-					memset(GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorType, 0x00, SENSOR_NUM_MAX * 2);
+					memset(GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorType, 0x00, SENSOR_NUM_MAX * 2);
-					GateWay->ConfigPara.Rs485Ch2.CUData.Para.CommStatus = true;
+					GateWay->ConfigPara.Rs485Ch2.CUPara.Para.CommStatus = true;
 					RS485Ch2_Config(9600);
 					GateWay->ConfigPara.Rs485Ch2.BaudRate = 9600;
 					SComm2Para.SensorCnt = 0;
@@ -323,11 +324,11 @@ void DebugCmdRS485Ctrl(int argc, char *argv[])
 			else if(strstr(argv[3], "off") != NULL){
 				if(idx == 1) {
 					GateWay->ConfigPara.Rs485Ch1.CommUnitEnable = false;
-					GateWay->ConfigPara.Rs485Ch1.CUData.Para.CommStatus = false;
+					GateWay->ConfigPara.Rs485Ch1.CUPara.Para.CommStatus = false;
 				}
 				else if(idx == 2) {
 					GateWay->ConfigPara.Rs485Ch2.CommUnitEnable = false;
-					GateWay->ConfigPara.Rs485Ch2.CUData.Para.CommStatus = false;
+					GateWay->ConfigPara.Rs485Ch2.CUPara.Para.CommStatus = false;
 				}
 				DBG_LOG("RS485Ch%d Disable!\r\n", idx);
 			}
@@ -452,11 +453,10 @@ void DebugCmdDelCommUnit(int argc, char *argv[])
 		return;
 	}
 	GateWay->ConfigPara.CommUnitArray[ret].RegFlag = false;
-	//memset(&GateWay->ConfigPara.CommUnitArray[ret], 0x00, sizeof(CommUnitData_t));
+	
 	DBG_LOG("Device has been deleted!\r\n");
 	WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
 }
-
 /*****************************************************************************************
 * 函数名称: DebugCmdLsCommUnit
 * 功能描述: 查看通讯单元信息
@@ -476,10 +476,10 @@ void DebugCmdLsCommUnit(int argc, char *argv[])
 	if(GateWay->ConfigPara.Rs485Ch1.CommUnitEnable == true) {
 		DBG_LOG("DevType: 8001\r\n");
 		DBG_LOG("DevMac: 01-80-02-00-00-01\r\n");
-		DBG_LOG("SensorNum: %d\r\n", GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorN);
+		DBG_LOG("SensorNum: %d\r\n", GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorN);
 		DBG_LOG("SensorType: ");
-		for(int i = 0; i < GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorN; i++) {
+		for(int i = 0; i < GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorN; i++) {
-			DBG_LOG("%04X ", GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorType[i]);
+			DBG_LOG("%04X ", GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorType[i]);
 		}
 		DBG_LOG("\r\n\r\n");
 	}
@@ -487,10 +487,10 @@ void DebugCmdLsCommUnit(int argc, char *argv[])
 	if(GateWay->ConfigPara.Rs485Ch2.CommUnitEnable == true) {
 		DBG_LOG("DevType: 8002\r\n");
 		DBG_LOG("DevMac: 01-80-02-00-00-02\r\n");
-		DBG_LOG("SensorNum: %d\r\n", GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorN);
+		DBG_LOG("SensorNum: %d\r\n", GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorN);
 		DBG_LOG("SensorType: ");
-		for(int i = 0; i < GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorN; i++) {
+		for(int i = 0; i < GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorN; i++) {
-			DBG_LOG("%04X ", GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorType[i]);
+			DBG_LOG("%04X ", GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorType[i]);
 		}
 		DBG_LOG("\r\n\r\n");
 	}
@@ -521,7 +521,143 @@ void DebugCmdLsCommUnit(int argc, char *argv[])
 		DBG_LOG("No device is registered.\r\n");
 	}
 }
+/*****************************************************************************************
+* 函数名称: DebugCmdExclCommUnit
+* 功能描述: 排除指定的通讯单元MAC
+* 参    数: argc, 输入参数数量
+						argv, 输入参数
+* 返 回 值: 无
+*****************************************************************************************/
+void DebugCmdExclCommUnit(int argc, char *argv[])
+{
+	DBG_LOG("\r\n");
+	uint8_t mac[6];
+	
+	if(argc < 2)
+		return;
+	
+	if(strcmp(argv[1], "?") == 0) {
+		DBG_LOG("Debug Cmd: excu arg1\r\n");
+		DBG_LOG("  brief --> Exclude communication unit.\r\n");
+		DBG_LOG("  arg1  --> mac: communication unit Mac address.\r\n");
+		DBG_LOG("            mac = (XX-XX-XX-XX-XX-XX), Exclude the MAC of the specified communication unit.\r\n\r\n");
+		return;
+	}
+  
+	int ret = sscanf(argv[1], "%x-%x-%x-%x-%x-%x", 
+									(int *)&mac[0], (int *)&mac[1], (int *)&mac[2], (int *)&mac[3], (int *)&mac[4], (int *)&mac[5]);
+	if(ret != 6) {
+		DBG_LOG("cuex Cmd Para Error!\r\n");
+		return;
+	}
+  
+	ret = CheckCommUnitExcl(GateWay, mac);
+	if(ret > -1) {
+		DBG_LOG("This device has been tested and eliminated at this gateway!\r\n");
+		return;
+	}
 
+  for(int i = 0; i < COMMUNIT_NUM_MAX; i++) {//寻找空位
+		if(GateWay->ConfigPara.ExclCommUnit[i].ExclFlag == false){
+      GateWay->ConfigPara.ExclCommUnit[i].ExclFlag = true;
+      memcpy(&GateWay->ConfigPara.ExclCommUnit[i].ExclMac, &mac[0], 6);
+      break;
+    }
+	}
+  
+  ret = CheckCommUnitReg(GateWay, mac);//删除注册信息
+	if(ret > -1) {
+		GateWay->ConfigPara.CommUnitArray[ret].RegFlag = false;
+	}
+  
+	DBG_LOG("Equipment removal was successful!\r\n");
+	WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
+}
+/*****************************************************************************************
+* 函数名称: DebugCmdDelExclCommUnit
+* 功能描述: 删除指定的被排除的通信单元MAC
+* 参    数: argc, 输入参数数量
+						argv, 输入参数
+* 返 回 值: 无
+*****************************************************************************************/
+void DebugCmdDelExclCommUnit(int argc, char *argv[])
+{
+	DBG_LOG("\r\n");
+	uint8_t mac[6];
+	
+	if(argc < 2)
+		return;
+	
+	if(strcmp(argv[1], "?") == 0) {
+		DBG_LOG("Debug Cmd: exdel arg1\r\n");
+		DBG_LOG("  brief --> Delete the excluded communication units.\r\n");
+		DBG_LOG("  arg1  --> mac: communication unit Mac address.\r\n");
+		DBG_LOG("            mac = (XX-XX-XX-XX-XX-XX), Delete the MAC address of the specified excluded communication unit.\r\n\r\n");
+		return;
+	}
+  
+  if(strcmp(argv[1], "all") == 0) {
+		for(uint8_t i = 0; i < COMMUNIT_NUM_MAX; i++)
+		{
+			GateWay->ConfigPara.ExclCommUnit[i].ExclFlag = false;
+		}
+		DBG_LOG("All excluded devices have been deleted!\r\n");
+		WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
+		return;
+	}	
+  
+	int ret = sscanf(argv[1], "%x-%x-%x-%x-%x-%x", 
+									(int *)&mac[0], (int *)&mac[1], (int *)&mac[2], (int *)&mac[3], (int *)&mac[4], (int *)&mac[5]);
+	if(ret != 6) {
+		DBG_LOG("exdel Cmd Para Error!\r\n");
+		return;
+	}
+  
+	ret = CheckCommUnitExcl(GateWay, mac);
+	if(ret < 0) {
+		DBG_LOG("This equipment has not been ruled out!\r\n");
+		return;
+	}
+
+  GateWay->ConfigPara.ExclCommUnit[ret].ExclFlag = false;  
+	DBG_LOG("The exclusion for this equipment has been cancelled!\r\n");
+	WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
+}
+
+/*****************************************************************************************
+* 函数名称: DebugCmdLsExclCommUnit
+* 功能描述: 查看被排除的通讯单元信息
+* 参    数: argc, 输入参数数量
+						argv, 输入参数
+* 返 回 值: 无
+*****************************************************************************************/
+void DebugCmdLsExclCommUnit(int argc, char *argv[])
+{
+	DBG_LOG("\r\n");
+	if(strcmp(argv[1], "?") == 0) {
+		DBG_LOG("Debug Cmd: exls\r\n\
+  brief --> View the information of the excluded communication units.\r\n\r\n");
+		return;
+	}
+	
+	int CUCnt = 0;
+	for(int i = 0; i < COMMUNIT_NUM_MAX; i++) {
+		if(GateWay->ConfigPara.ExclCommUnit[i].ExclFlag == true) {
+			CUCnt++;
+			DBG_LOG("Exclude DevMac: %02X-%02X-%02X-%02X-%02X-%02X\r\n", 
+							GateWay->ConfigPara.ExclCommUnit[i].ExclMac[0], 
+							GateWay->ConfigPara.ExclCommUnit[i].ExclMac[1], 
+							GateWay->ConfigPara.ExclCommUnit[i].ExclMac[2],
+							GateWay->ConfigPara.ExclCommUnit[i].ExclMac[3], 
+							GateWay->ConfigPara.ExclCommUnit[i].ExclMac[4], 
+							GateWay->ConfigPara.ExclCommUnit[i].ExclMac[5]);
+		}
+	}
+	if(CUCnt ==0) {
+		DBG_LOG("No device is exclude.\r\n");
+	}
+  DBG_LOG("\r\n\r\n");
+}
 /*****************************************************************************************
 * 函数名称: DebugCmdSetComm
 * 功能描述: 设置网关与服务通讯方式
@@ -536,14 +672,16 @@ void DebugCmdSetComm(int argc, char *argv[])
 		return;
 	
 	if(strcmp(argv[1], "?") == 0) {
-		DBG_LOG("Debug Cmd: comm	arg1\r\n");
+		DBG_LOG("Debug Cmd: comm arg1\r\n");
 		DBG_LOG("  brief --> Set gateway and service communication methods.\r\n");
 		DBG_LOG("  arg1  --> para: (cat1, eth),Cat1 or ETH communication.\r\n\r\n");
 		return;
 	}
 	
 	if(strcmp(argv[1], "cat1") == 0) {
+		GateWay->SvrRegFlag = false;
 		GateWay->ConfigPara.Comm = CATONE_COMM;
+		ETHStop();
 		CAT1_ON();
 		CatOneReset();
 		DBG_LOG("Set the communication method to Cat1.\r\n");
@@ -557,12 +695,12 @@ void DebugCmdSetComm(int argc, char *argv[])
 			rt_thread_delay(3000);
 			CAT1_PWR_KEY_SET();
 		}
-	
+		GateWay->SvrRegFlag = false;
 		GateWay->ConfigPara.Comm = ETH_COMM;
 		ETH_ON();
+		ETHReset();
 		WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
 	}
-	
 }
 
 /*****************************************************************************************
@@ -747,18 +885,94 @@ void DebugCmdRestoreFactory(int argc, char *argv[])
 	DBG_LOG("\r\n");
 	if(strcmp(argv[1], "?") == 0) {
 		DBG_LOG("Debug Cmd: res\r\n\
-  brief --> Restore to factory.\r\n\r\n");
+  brief --> Restore to factory.\r\n");
+		DBG_LOG("  arg1  --> password\r\n\r\n");
 		return;
 	}
 	
+	if(strcmp(argv[1], "gxjt") != 0) {
+		DBG_LOG("Password Error\r\n");
+		return;
+	}
+		
+	DBG_LOG("Restore factory settings, GateWay Restart...\r\n");
 	memset((uint8_t *)&GateWay->ConfigPara, 0x00, sizeof(GWConfigPara_t));
 	WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
-	DBG_LOG("Restore factory settings, GateWay Restart...\r\n");
 	rt_thread_delay(1000);
 	NVIC_SystemReset();
 	while(1);
 }
 
+/*****************************************************************************************
+* 函数名称: DebugCmdUpload
+* 功能描述: 上传当前网关状态
+* 参    数: argc, 输入参数数量
+						argv, 输入参数
+* 返 回 值: 无
+*****************************************************************************************/
+static void DebugCmdUpload(int argc, char *argv[])
+{
+	DBG_LOG("\r\n");
+	if(strcmp(argv[1], "?") == 0) {
+		DBG_LOG("Debug Cmd: up\r\n");
+		DBG_LOG("  brief --> Upload current gateway status to server.\r\n\r\n");
+		return;
+	}
+
+	if(GateWay->SvrRegFlag == false) {
+		DBG_LOG("Server not registered, please register first.\r\n");
+		return;
+	}
+
+	uint8_t MegData[6];
+	uint8_t len = sizeof(GateWayAlarmType_t);
+	MegData[0] = len & 0x00ff;
+	MegData[1] = (len >> 8) & 0x00ff;
+	MegData[2] = NET_COMM_CMD_ALARM;
+
+	MegData[3] = 0x00;
+	MegData[4] = GateWay->ConfigPara.OutageFlag ? 1 : 0;
+	MegData[5] = GateWay->Battery;
+
+	if(CatOneEthSendQueue(MegData, 6) == true) {
+		DBG_LOG("Gateway status uploaded.\r\n");
+	}
+	else {
+		DBG_LOG("Gateway status upload failed.\r\n");
+	}
+}
+
+/*****************************************************************************************
+* 函数名称: DebugCmdRegister
+* 功能描述: 重新向上位机发起注册
+* 参    数: argc, 输入参数数量
+						argv, 输入参数
+* 返 回 值: 无
+*****************************************************************************************/
+static void DebugCmdRegister(int argc, char *argv[])
+{
+	DBG_LOG("\r\n");
+	if(strcmp(argv[1], "?") == 0) {
+		DBG_LOG("Debug Cmd: reg\r\n");
+		DBG_LOG("  brief --> Re-register to the server.\r\n\r\n");
+		return;
+	}
+
+	GateWay->SvrRegFlag = false;
+
+	if(GateWay->ConfigPara.Comm == CATONE_COMM) {
+		CatOneTriggerRegister();
+		DBG_LOG("Trigger Cat1 re-registration immediately.\r\n");
+	}
+	else if(GateWay->ConfigPara.Comm == ETH_COMM) {
+		ETHTriggerRegister();
+		DBG_LOG("Trigger ETH re-registration immediately.\r\n");
+	}
+	else {
+		DBG_LOG("Unknown communication type.\r\n");
+	}
+}
+
 /*****************************************************************************************
 * 函数名称: DebugCmdRestoreFactory
 * 功能描述: 恢复出厂设置
@@ -863,7 +1077,7 @@ void DebugCmdTimeSync(int argc, char *argv[])
 		return;
 	
 	if(strcmp(argv[1], "?") == 0) {
-		DBG_LOG("Debug Cmd: time\r\n");
+		DBG_LOG("Debug Cmd: time args\r\n");
 		DBG_LOG("  brief --> Time synchronization.\r\n");
 		DBG_LOG("  args  --> (time YYYY-MM-DD,hh:mm:ss)Set system time.\r\n\r\n");
 		return;
@@ -910,15 +1124,15 @@ void DebugCmdQuerySensor(int argc, char *argv[])
 	if(GateWay->ConfigPara.Rs485Ch1.Enable == true && GateWay->ConfigPara.Rs485Ch1.CommUnitEnable == true) {
 		DBG_LOG("Query Rs485Ch1...\r\n");
 		GateWay->ConfigPara.Rs485Ch1.QuerySensorFlag = true;
-		GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorN = 0;
+		GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorN = 0;
-		memset(GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorType, 0x00, sizeof(GateWay->ConfigPara.Rs485Ch1.CUData.Para.SensorType));
+		memset(GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorType, 0x00, sizeof(GateWay->ConfigPara.Rs485Ch1.CUPara.Para.SensorType));
 		SComm1Para.SensorCnt = 0;
 	}
 	if(GateWay->ConfigPara.Rs485Ch2.Enable == true && GateWay->ConfigPara.Rs485Ch2.CommUnitEnable == true) {
 		DBG_LOG("Query Rs485Ch2...\r\n");
 		GateWay->ConfigPara.Rs485Ch2.QuerySensorFlag = true;
-		GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorN = 0;
+		GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorN = 0;
-		memset(GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorType, 0x00, sizeof(GateWay->ConfigPara.Rs485Ch2.CUData.Para.SensorType));
+		memset(GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorType, 0x00, sizeof(GateWay->ConfigPara.Rs485Ch2.CUPara.Para.SensorType));
 		SComm2Para.SensorCnt = 0;
 	}
 }
@@ -938,7 +1152,7 @@ void DebugCmdSelDebugChannel(int argc, char *argv[])
 		return;
 	
 	if(strcmp(argv[1], "?") == 0) {
-		DBG_LOG("Debug Cmd: dch\r\n");
+		DBG_LOG("Debug Cmd: dch args\r\n");
 		DBG_LOG("  brief --> Debug information output channel selection.\r\n");
 		DBG_LOG("  args  --> (dbg|ch1|ch2) default: dbg\r\n");
 		DBG_LOG("            dbg: On board debugging serial port.\r\n");
@@ -993,26 +1207,31 @@ static void DebugCmdSetSvr(int argc, char *argv[])
 	int IP[4];
 	int port;
 	
-	if(argc < 3)
+	if(argc < 2)
 		return;
 	
 	if(strcmp(argv[1], "?") == 0) {
-		DBG_LOG("Debug Cmd: arg1 arg2\r\n");
+		DBG_LOG("Debug Cmd: svr arg1 arg2 arg3\r\n");
 		DBG_LOG("  brief --> Set the server IP address and port for 4G communication.\r\n");
-		DBG_LOG("  arg1  --> (xx.xx.xx.xx) ip\r\n");
+		DBG_LOG("  arg1  --> password\r\n");
-		DBG_LOG("  arg2  --> port\r\n\r\n");
+		DBG_LOG("  arg2  --> (xx.xx.xx.xx) ip\r\n");
+		DBG_LOG("  arg3  --> port\r\n\r\n");
 		return;
 	}
 	
-	char *IpStr = argv[1];
+	if(strcmp(argv[1], "gxjt") != 0) {
-
+		DBG_LOG("Password Error\r\n");
+		return;
+	}
+	
+	char *IpStr = argv[2];
 	int ret = sscanf(IpStr, "%d.%d.%d.%d", &IP[0], &IP[1], &IP[2], &IP[3]);
 	if(ret != 4)
 		return;
 	if(IP[0] > 0xff || IP[1] > 0xff || IP[2] > 0xff || IP[3] > 0xff)
 		return;
 	
-	port = atoi(argv[2]);
+	port = atoi(argv[3]);
 	if(port > 0xffff)
 		return;
 	
@@ -1044,7 +1263,7 @@ static void DebugCmdSetMac(int argc, char *argv[])
 	if(strcmp(argv[1], "?") == 0) {
 		DBG_LOG("Debug Cmd: mac arg1 arg2\r\n");
 		DBG_LOG("  brief --> Set the server IP address and port for 4G communication.\r\n");
-		DBG_LOG("  arg1  --> psw\r\n");
+		DBG_LOG("  arg1  --> password\r\n");
 		DBG_LOG("  arg2  --> mac(xx-xx-xx-xx-xx-xx)\r\n\r\n");
 		return;
 	}
@@ -1106,24 +1325,25 @@ static void DebugCmdGetPara(int argc, char *argv[])
 	DBG_LOG("Svr Port: %d\r\n", GateWay->ConfigPara.SvrPort);
 	DBG_LOG("Register Status: %d\r\n", GateWay->SvrRegFlag);
 	DBG_LOG("RS485Ch1 Mac: %02X-%02X-%02X-%02X-%02X-%02X\r\n",
-					GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0][0],GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0][1],
+					GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0][0],GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0][1],
-					GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0][2],GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0][3],
+					GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0][2],GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0][3],
-					GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0][4],GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0][5]);
+					GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0][4],GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0][5]);
 	DBG_LOG("RS485Ch1: %s, ", (GateWay->ConfigPara.Rs485Ch1.Enable == true) ? "Enable" : "Disable");
 	DBG_LOG("InCommUnit %s, ", (GateWay->ConfigPara.Rs485Ch1.CommUnitEnable == true) ? "Enable" : "Disable");
 	DBG_LOG("Vout %s, ", (GateWay->ConfigPara.Rs485Ch1.Power == true) ? "Enable" : "Disable");
 	DBG_LOG("Baudrate %d\r\n", GateWay->ConfigPara.Rs485Ch1.BaudRate);
 	DBG_LOG("RS485Ch2 Mac: %02X-%02X-%02X-%02X-%02X-%02X\r\n",
-					GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0][0],GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0][1],
+					GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0][0],GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0][1],
-					GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0][2],GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0][3],
+					GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0][2],GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0][3],
-					GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0][4],GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0][5]);
+					GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0][4],GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0][5]);
 	DBG_LOG("RS485Ch2: %s, ", (GateWay->ConfigPara.Rs485Ch2.Enable == true) ? "Enable" : "Disable");
 	DBG_LOG("InCommUnit %s, ", (GateWay->ConfigPara.Rs485Ch2.CommUnitEnable == true) ? "Enable" : "Disable");
 	DBG_LOG("Vout %s, ", (GateWay->ConfigPara.Rs485Ch2.Power == true) ? "Enable" : "Disable");
 	DBG_LOG("Baudrate %d\r\n", GateWay->ConfigPara.Rs485Ch2.BaudRate);
 	
 	DBG_LOG("Lora: ch %d, rp %d, fc %d\r\n", GateWay->ConfigPara.Lora.ucChannel, GateWay->ConfigPara.Lora.RegPreamble, GateWay->ConfigPara.Lora.FreqCent);
-	
+	DBG_LOG("LpCfg:  CI:%dsec, RI:%dmin, EI:%dmin, ET:%dmin\r\n", 
+		LW_DEV_COLLECT_INTERVAL_MAX, LW_DEV_REPORT_INTERVAL_MAX, LW_DEV_ER_INTERVAL_MAX, LW_DEV_ER_TIME_MAX);
 	struct tm *stime;
 	uint32_t dwStamp = TimeTs();
   stime = localtime(&dwStamp);
@@ -1133,7 +1353,7 @@ static void DebugCmdGetPara(int argc, char *argv[])
   DBG_LOG("%d:",stime->tm_hour);
   DBG_LOG("%d:",stime->tm_min);
   DBG_LOG("%d\r\n",stime->tm_sec);
-	DBG_LOG("**********************************************************\r\n");
+  DBG_LOG("**********************************************************\r\n");
 }
 
 /*****************************************************************************************
@@ -1156,7 +1376,7 @@ static void DebugCmdCali(int argc, char *argv[])
 	
 	if(argc > 1) {
 		if(strcmp(argv[1], "?") == 0) {
-			DBG_LOG("Debug Cmd: cali\r\n");
+			DBG_LOG("Debug Cmd: cali arg1\r\n");
 			DBG_LOG("  brief --> Calibrate the sensor.\r\n\r\n");
 			DBG_LOG("  arg1  --> mac: communication unit Mac address.\r\n");
 			DBG_LOG("            mac = (XX-XX-XX-XX-XX-XX), Calibrate specified MAC communication unit.\r\n");
@@ -1212,7 +1432,7 @@ static void DebugCmdCali(int argc, char *argv[])
 		return;
 	}
 	
-	if(memcmp(mac, GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0], 6) == 0) {
+	if(memcmp(mac, GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0], 6) == 0) {
 		if(!GateWay->ConfigPara.Rs485Ch1.Enable || !GateWay->ConfigPara.Rs485Ch1.CommUnitEnable) {
 			DBG_LOG("Internal communication unit 1 is turned off!\r\n");
 			return;
@@ -1222,7 +1442,7 @@ static void DebugCmdCali(int argc, char *argv[])
 		return;
 	}
 	
-	if(memcmp(mac, GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0], 6) == 0) {
+	if(memcmp(mac, GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0], 6) == 0) {
 		if(!GateWay->ConfigPara.Rs485Ch2.Enable || !GateWay->ConfigPara.Rs485Ch2.CommUnitEnable) {
 			DBG_LOG("Internal communication unit 2 is turned off!\r\n");
 			return;
@@ -1285,8 +1505,8 @@ static void DebugLaserConfig(int argc, char *argv[])
 	
 	if(argc > 1) {
 		if(strcmp(argv[1], "?") == 0) {
-			DBG_LOG("Debug Cmd: laser\r\n");
+			DBG_LOG("Debug Cmd: laser arg1 arg2\r\n");
-			DBG_LOG("  brief --> Control laser cutting.\r\n\r\n");
+			DBG_LOG("  brief --> Control laser cutting.\r\n");
 			DBG_LOG("  arg1  --> mac: communication unit Mac address.\r\n");
 			DBG_LOG("            mac = (XX-XX-XX-XX-XX-XX), Control specified MAC communication unit.\r\n");
 			DBG_LOG("  arg2  --> state: on/off, Turn on or off the laser.\r\n\r\n");
@@ -1311,7 +1531,7 @@ static void DebugLaserConfig(int argc, char *argv[])
 	
 	if(strcmp(argv[2], "on") == 0 || strcmp(argv[2], "off") == 0)
 	{
-		if(memcmp(mac, GateWay->ConfigPara.Rs485Ch1.CUData.Para.Mac[0], 6) == 0) {
+		if(memcmp(mac, GateWay->ConfigPara.Rs485Ch1.CUPara.Para.Mac[0], 6) == 0) {
 			if(!GateWay->ConfigPara.Rs485Ch1.Enable || !GateWay->ConfigPara.Rs485Ch1.CommUnitEnable) {
 				DBG_LOG("Internal communication unit 1 is turned off!\r\n");
 				return;
@@ -1321,7 +1541,7 @@ static void DebugLaserConfig(int argc, char *argv[])
 			return;
 		}
 	
-		if(memcmp(mac, GateWay->ConfigPara.Rs485Ch2.CUData.Para.Mac[0], 6) == 0) {
+		if(memcmp(mac, GateWay->ConfigPara.Rs485Ch2.CUPara.Para.Mac[0], 6) == 0) {
 			if(!GateWay->ConfigPara.Rs485Ch2.Enable || !GateWay->ConfigPara.Rs485Ch2.CommUnitEnable) {
 				DBG_LOG("Internal communication unit 2 is turned off!\r\n");
 				return;
@@ -1410,10 +1630,10 @@ static void DebugCmdLPConfig(int argc, char *argv[])
 	if(strcmp(argv[1], "?") == 0) {
 		DBG_LOG("Debug Cmd: lpcfg arg1 arg2 arg3 arg4\r\n");
 		DBG_LOG("  brief --> Configure low-power device parameters.\r\n");
-		DBG_LOG("  arg1  --> Collect interval\r\n");
+		DBG_LOG("  arg1  --> Collect interval(30~7200 second)\r\n");
-		DBG_LOG("  arg2  --> Report interval\r\n");
+		DBG_LOG("  arg2  --> Report interval(5~720 minute)\r\n");
-		DBG_LOG("  arg3  --> Emergency reporting interval\r\n");
+		DBG_LOG("  arg3  --> Emergency reporting interval(1~5 minute)\r\n");
-		DBG_LOG("  arg4  --> Emergency reporting time\r\n\r\n");
+		DBG_LOG("  arg4  --> Emergency reporting time(10~120 minute)\r\n\r\n");
 		return;
 	}
 	
@@ -1460,7 +1680,7 @@ static void DebugCmdLPConfig(int argc, char *argv[])
 
 /*****************************************************************************************
 * 函数名称: DebugCmdLPConfig
-* 功能描述: 低功耗参数配置
+* 功能描述: Lora参数配置
 * 参    数: argc, 输入参数数量
 						argv, 输入参数
 * 返 回 值: 无
@@ -1472,7 +1692,7 @@ static void DebugLoraConfig(int argc, char *argv[])
 		return;
 	
 	if(strcmp(argv[1], "?") == 0) {
-		DBG_LOG("Debug Cmd: Lora arg1 arg2\r\n");
+		DBG_LOG("Debug Cmd: lora arg1 arg2\r\n");
 		DBG_LOG("  brief --> Configure Lora parameters.\r\n");
 		DBG_LOG("  arg1  --> ch: Channel--para=(0~16)\r\n");
 		DBG_LOG("            pw: Power--para=(0~20)\r\n");
@@ -1480,6 +1700,7 @@ static void DebugLoraConfig(int argc, char *argv[])
 		DBG_LOG("            sf: SpreadFactor--para=(6~12)\r\n");
 		DBG_LOG("            ec: ErrorCoding--para=(1~4)\r\n");
 		DBG_LOG("            rp: RegPreamble--para=(1~32)\r\n");
+		DBG_LOG("            fc: FreqCent--para=(410000000~525000000)\r\n");
 		DBG_LOG("            o: on/off\r\n");
 		DBG_LOG("  arg2  --> para\r\n");
 
@@ -1570,7 +1791,18 @@ static void DebugLoraConfig(int argc, char *argv[])
 			return;
 		}
 	}
-	if(GateWay->ConfigPara.Lora.OnOff)
+	if(strcmp(argv[1], "fc") == 0){
+		uint32_t fc = atoi(argv[2]);
+		if(LoraSetFreqCent(fc)) {
+			GateWay->ConfigPara.Lora.FreqCent = fc;
+			DBG_LOG(" Lora FreqCent is configured successfully!\r\n");
+		}
+		else {
+			DBG_LOG("Lora Para Error!\r\n");
+			return;
+		}
+	}
+	if(GateWay->ConfigPara.Lora.OnOff == true)
 		LoraInit();
 	WritePara((uint8_t *)&GateWay->ConfigPara, sizeof(GWConfigPara_t));
 	DBG_LOG("Lora reinitializes.\r\n");
@@ -1609,7 +1841,19 @@ void DebugCmdHelp(int argc, char *argv[])
 	len = strlen("culs ?\r\n");
 	memcpy(Data, "culs ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
+  
+  len = strlen("excu ?\r\n");
+	memcpy(Data, "excu ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+  
+  len = strlen("exdel ?\r\n");
+	memcpy(Data, "exdel ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
 	
+  len = strlen("exls ?\r\n");
+	memcpy(Data, "exls ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+  
 	len = strlen("comm ?\r\n");
 	memcpy(Data, "comm ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
@@ -1630,22 +1874,14 @@ void DebugCmdHelp(int argc, char *argv[])
 	memcpy(Data, "hinf ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
 	
-//	len = strlen("res ?\r\n");
+	len = strlen("res ?\r\n");
-//	memcpy(Data, "res ?\r\n", len);
+	memcpy(Data, "res ?\r\n", len);
-//	DebugAnalyze(GateWay, Data, len);
-	
-	len = strlen("sct ?\r\n");
-	memcpy(Data, "sct ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
-	
+
 	len = strlen("time ?\r\n");
 	memcpy(Data, "time ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
 	
-	len = strlen("svr ?\r\n");
-	memcpy(Data, "svr ?\r\n", len);
-	DebugAnalyze(GateWay, Data, len);
-	
 	len = strlen("qs ?\r\n");
 	memcpy(Data, "qs ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
@@ -1654,24 +1890,63 @@ void DebugCmdHelp(int argc, char *argv[])
 	memcpy(Data, "dch ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
 	
+	len = strlen("svr ?\r\n");
+	memcpy(Data, "svr ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+	
+	len = strlen("mac ?\r\n");
+	memcpy(Data, "mac ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+	
 	len = strlen("para ?\r\n");
 	memcpy(Data, "para ?\r\n", len);
 	DebugAnalyze(GateWay, Data, len);
+	
+	len = strlen("cali ?\r\n");
+	memcpy(Data, "cali ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+	
+	len = strlen("laser ?\r\n");
+	memcpy(Data, "laser ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+	
+	len = strlen("lpcfg ?\r\n");
+	memcpy(Data, "lpcfg ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+	
+	len = strlen("lora ?\r\n");
+	memcpy(Data, "lora ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+	
+	len = strlen("reboot ?\r\n");
+	memcpy(Data, "reboot ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+
+	len = strlen("up ?\r\n");
+	memcpy(Data, "up ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
+
+	len = strlen("reg ?\r\n");
+	memcpy(Data, "reg ?\r\n", len);
+	DebugAnalyze(GateWay, Data, len);
 }
 
 const DBGFunType DebugFun[DEBUG_CMD_CNT] = {
 	"help",				DebugCmdHelp,
 	"main",				DebugCmdMainOnOff,
 	"cat1",				DebugCmdCat1OnOff,
-	"rs485",				DebugCmdRS485Ctrl,
+	"rs485",			DebugCmdRS485Ctrl,
-	"cudel",				DebugCmdDelCommUnit,
+	"cudel",			DebugCmdDelCommUnit,
 	"culs",				DebugCmdLsCommUnit,
+  "excu",       DebugCmdExclCommUnit,
+  "exdel",      DebugCmdDelExclCommUnit,
+  "exls",       DebugCmdLsExclCommUnit,
 	"comm",				DebugCmdSetComm,
 	"sct",				DebugCmdSetCollectTime,
-//	"his",				DebugCmdReadHisData,
+	"his",				DebugCmdReadHisData,
 	"fmt",				DebugCmdDelHisData,
 	"hinf",				DebugCmdGetHisInfo,
-//	"res",				DebugCmdRestoreFactory,
+	"res",				DebugCmdRestoreFactory,
 	"time",				DebugCmdTimeSync,
 	"qs",					DebugCmdQuerySensor,
 	"dch",				DebugCmdSelDebugChannel,
@@ -1679,8 +1954,10 @@ const DBGFunType DebugFun[DEBUG_CMD_CNT] = {
 	"mac",				DebugCmdSetMac,
 	"para",				DebugCmdGetPara,
 	"cali",				DebugCmdCali,
-	"laser",				DebugLaserConfig,
+	"laser",			DebugLaserConfig,
-	"lpcfg",				DebugCmdLPConfig,
+	"lpcfg",			DebugCmdLPConfig,
 	"lora",				DebugLoraConfig,
 	"reboot",			DebugCmdReboot,
+	"up",				  DebugCmdUpload,
+	"reg",				DebugCmdRegister,
 };

README.md

@@ -1,2 +1,5 @@
-# HC32F460_DebugCmd
+# GateWay_Debug
+# 适用于Gateway项目
+# 单片机HC32F460
+# 转换为模块仓库 2026-05-14